Opel Combo 2001 2011 Brake Light Reversing Camera Backup & Flip Monitor

Reversing Camera & Flip Monitor For Opel Combo. This camera is designed to replace the 3rd brake light situated on the rear of the vehicle.

Please note this listing comes with everything required to install this system. The old light is simply removed and replaced with this unit. A 10m cable then is run to your monitor at the front of the vehicle. Please see the instructions below to see installations instructions.

Min illumination:0Lux (LED ON). Perfect IR night vision, 8 pcs IR LED.

White Balance: Auto, Video Colour: Colourful. Effective Pixels : 756(H)504(V).

Video Output: 1.0Vp-p, 75. S/N ratio: Better Than 48db. Working Power (DC): 12V/1,5.

Watt Current consumption: 90mA Max. Video cable is RCA connector. 4.3 Flip Monitor Description. Screen Size: 4.3(16:9). Item Size: Approx 13.4 11.2 2.5cm / 5.28 4.41 0.98in.

Please note that the image cannot be flipped on this monitor so it cannot be fitted upside down. Installation tips:Two-way video inputs will display a black screen when no there is no signal. 2-channel video input:V1/ V2 auto switching(V1 display first). Note: Please Connect the Rearview camera's video cable with LCD's yellow cable (Video V1). Then the LCD will show Camera's video when you are Reversing, and stop playing movie (auto switching).

Folding design enables the monitor to close out of sight to protect against thieves. 10 meter 4 pin extension cable. 12v Power adaptor for camera. 12v Power adapter for Monitor. Please refer to the diagram for reference which can be found in the in images for this listing.

We recommend before installing the product in place test everything to check that it works. First thing to consider is which power source you are going to use to turn on the camera. This can be done in a few ways and is specific to each vehicle, but this can be done by. Using the wire signal coming from when reverse is engaged. Using the reverse gear signal wire on the loom for an aftermarket stereo. Using a scotch lock and use the power source from the reversing light. This option will require running an additional cable to the front of the Vehicle. This power source can be used for the camera. (1) and the monitor (7) should you want them both to turn on only when reverse is engaged. Below is a description of each wire.

(1) Red - 12v power supply. (3) Yellow - CameraCamera side wiring. (4) Red - Positive from existing brake light. (5) Black - Ground from existing brake light.

(7) Red - 12v power supply (fused) Can use same power feed as camera. (9) Yellow - Av source 1 (Camera). (10) White - Av source 2 (DVD player or Dash cam).

(11) Male to Male Av connector Used to connect cables (3) & (9) together. If the parking lines are turned off as default and you require them simply cut the brown loop which is exposed on the wiring loom. Ideally the 10m cable should be installed inside the van with the panels inside removed. For applications where this is not possible the cable can be run externally but be aware damage can be caused by debris off the road and heat from the exhaust. Should you have issues with the brake light not working this can be because the polarity is the incorrect around meaning the positive and negative need to be switched. The Stock house is a small business where you will find great products at bargain prices. We specialise in getting you the products you want when you need them. Stocking a wide range of products we are dedicated to giving you a good customer service. We hope you enjoy your shopping experience and we look forward to welcoming you back soon. We aim to answer all questions within 24 hours, excluding weekends and holidays. This item is in the category "Vehicle Parts & Accessories\Car Parts & Accessories\Advanced Driver Assistance Systems\Parking Assistance\Parking Cameras".

The seller is "the-stock-house" and is located in this country: GB. This item can be shipped worldwide.